DeviceNet Router/B
A-DNTR/B
The DeviceNet Router/B provides a powerful and easy to configure solution to exchange data between DeviceNet™ and EtherNet/IP™, Modbus TCP/IP or Modbus RTU networks.
The module can be configured as a DeviceNet Scanner or a DeviceNet Device - allowing the user to not only integrate DeviceNet devices into a Logix or Modbus system, it also allows EtherNet/IP or Modbus devices in an existing DeviceNet network.
The DeviceNet Router B is configured using the Slate Configuration Utility software tool.
The DeviceNet Router B includes a web server to display DeviceNet operation and communication statistics and advanced diagnostics functions like built-in packet capture for the various protocols. The router has two Ethernet ports to support Device-Level-Ring (DLR) architectures
- Imágenes
- Características y Beneficios
- Configuración
- Especificaciones
- Hardware
- Descargas
- Certificaciones
Imágenes
|
|
|
|
|
|
|
|
Características y Beneficios
- DeviceNet Scanner or DeviceNet Device
- Support for multiple DeviceNet network baud rates (125K, 250K, 500K)
- Support for DeviceNet pass-through or explicit messaging
- PCCC client mode to connect to Ethernet-only PanelViews to an existing DeviceNet network
- EtherNet/IP Target or Originator with support for Class 1 connections
- Supports Modbus TCP/IP (Ethernet) and Modbus RTU (Serial) Client/Server
- Direct-to-Tag Technology
- Dual Ethernet ports with support for DLR (Device Level Ring)
- Support for NTP (Network Time Protocol) for external clock synchronization
- Advanced Diagnostics, including packet capture
Configuración
The Slate Configuration Utility software is used for the configuration and troubleshooting of the module. The stand-alone configuration utility allows users to define the setup and configuration of the DeviceNet Router module, connections with controllers and devices.
Especificaciones
DeviceNet Network
| Specification |
Description |
| Connector |
5-way terminal, 5.08 mm pitch. |
| Modes |
Scanner, Target (or Device) |
| Baud Rate |
125k, 250k, 500k |
| DeviceNet Terminator |
120 Ω (Software enabled) |
DeviceNet Scanner
| Specification |
Description |
| Device Count |
63 |
| Set Target Device Node |
Supported |
| Set Target Device Baud Rate |
Supported |
| Device Discovery |
Supported |
| Explicit Messaging |
Supported |
| Supported Connections |
Poll, Change of State (COS) |
DeviceNet Target
| Specification |
Description |
| Supported Connections |
Poll, Change of State (COS) |
| Input / Output Data Max |
256 bytes input or output, per message |
PCCC Network
| Specification |
Description |
| Max PCCC Connections |
10 |
| Max PCCC Payload |
1000 bytes |
EtherNet/IP Network
| Specification |
Description |
| Connector |
RJ45 |
| Conductors |
CAT5 STP/UTP |
| ARP Connections |
Max 100 |
| TCP Connections |
Max 100 |
| CIP Connections |
Max 15 |
| Communication Rate |
10/100 Mbps |
| Duplex Mode |
Full / Half |
| Auto-MDIX Support |
Yes |
| Embedded switch |
Yes, 2 x Ethernet ports |
| Device Level Ring (DLR) |
Yes |
| Network Time Protocol (NTP) |
Yes |
EtherNet/IP Originator
| Specification |
Description |
| Class 1 Cyclic Connections Supported |
Yes |
| Class 3 / UCMM Connections Supported |
Yes |
| Class 1 connection count |
10 |
| Class 3 / UCMM Target Device Count |
10 |
| Class 3 / UCMM Mapping Count |
50 |
EtherNet/IP Target
| Specification |
Description |
| Class 1 Cyclic connection count |
4 |
| Logix Direct-To-Tag supported |
Yes |
Modbus Client
| Specification |
Description |
| Modes |
Modbus TCP/IP, Modbus RTU (RS232 and 485) |
| Modbus RS485 Termination |
125 Ω (Software enabled) |
| Maximum Modbus Server Devices |
20 |
| Maximum Modbus Registers mapped |
100 |
| Modbus address Range supported |
0 to 65535 of each type (Holding/Input Register, Input/Coil Status) |
| Base Offset |
Modbus (Base 0) ; PLC (Base 1) |
| Configurable Modbus TCP port |
Yes |
| Data Reformatting Supported |
BB AA BB AA DD CC CC DD AA BB DD CC BB AA |
Modbus Server
| Specification |
Description |
| Modes |
Modbus TCP/IP, Modbus RTU (232 and 485) |
| Modbus RS485 Termination |
Software set |
| Modbus address Range supported |
0 to 65535 of each type (Holding/Input Register, Input/Coil Status) |
| Base Offset |
Modbus (Base 0) ; PLC (Base 1) |
| Configurable Modbus TCP/IP port |
Yes |
Serial Port (RS232)
| Specification |
Description |
| RS232 Connector |
9-way terminal (shared with RS485) |
| RS232 Conductor |
24 – 18 AWG |
| Electrical Isolation |
1000 VDC |
| Baud Rates |
1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 |
| Parity/Data Bits/Stop Bits |
None, Even, Odd / 8 / 1 |
Serial Port (RS485)
| Specification |
Description |
| RS232 Connector |
9-way terminal (shared with RS485) |
| RS232 Conductor |
24 – 18 AWG |
| Electrical Isolation |
1500 Vrms (1 minute, maximum) |
| Baud Rates |
1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 |
| Parity/Data Bits/Stop Bits |
None, Even, Odd / 8 / 1 |
Hardware
| Specification |
Description |
| Power Supply |
Input: 10 to 32 VDC, (85 mA @ 24 VDC and 180mA @ 10 VDC) |
| Power Consumption |
2.2 W |
| Dimensions |
149.0 x 34.0 x 116.0 mm (H x W x D) |
| Connector |
3-way terminal |
| Conductors |
24 to 18 AWG |
| Enclosure Rating |
IP20, NEMA/UL Open Type |
| Temperature |
-20 to 70 °C |
| Humidity |
0 to 95% RH, non-condensing |
| Earth Connection |
Yes, terminal based |
| Emissions |
IEC61000-6-4 |
| ESD Immunity |
EN 61000-4-2 |
| Radiated RF Immunity |
IEC 61000-4-3 |
| EFT/B Immunity |
IEC 61000-4-4 |
| Surge Immunity |
IEC 61000-4-5 |
| Conducted RF Immunity |
IEC 61000-4-6 |
Certificaciones
| UL/cUL; Class1, Div 2 | 238,99 kB | Última Modificación 25.01.2024 |
| CE Declaration of Conformity (CE, UKCA, RoHS, UL) | 339,65 kB | Última Modificación 26.01.2024 |
| ATEX Letter Of Conformity | 101,09 kB | Última Modificación 13.10.2023 |