Powerful network integration

•  Allows movement of data between dissimilar networks using two communication protocols on one gateway
•  Protocols share access to a common memory database to exchange data between networks
•  View diagnostic data for both networks from a single configuration/debug port

EtherNet/IP Client and Server

•  Integrate with widely available Rockwell Automation and third-party products and services worldwide
•  Client/server Explicit Messaging communication supported (PCCC-type messages)
•  Five server connections
•  One client connection provides up to 100 commands

IEC 60870-5-104 Client

•  Four connections for remote servers
•  Supports up to two Common ASDU Addresses per server
•  Supports monitored and control data
•  Supports up 500 commands to the remote servers
•  Timestamp events are available to the other protocol through the mailbox feature

The Explicit Messaging aspect of the protocol has been implemented to provide

asynchronous data transfer between the ProLinx gateway and Rockwell

Automation hardware.

Supported PLC Types

PLC-2®, PLC-3®, PLC-5®, SLC™500, ControlLogix®,

CompactLogix™, and MicroLogix™

Messaging Types

As a Client, PCCC Explicit Messaging

As a Server, PCCC or CIP Explicit Messaging

Command Sets

PLC-2/PLC-3/PLC5 Basic Command Set

PLC5 Binary Command Set

PLC5 ASCII Command Set

SLC500 Command Set

Number of Connections

5

Supported PLC Types

PLC2, PLC5, SLC and ControlLogix file types

supported

Internal Database

Data Table File Size: 100 or 1000 words

Data Table File Start: N10 to N109 (based on file

size set to 100) or

N10 to N19 (based on file set to 1000)

CIP Services Supported

0x4C - CIP Data Table Read

0x4D - CIP Data Table Write

Number of Clients Supported

1

Command List

Support for 100 commands per Client, each configurable for command type, IP address, register to/from addressing and word/bit count.

Polling of Command List

User-configurable polling of commands, including disabled, continuous and on change of data (write only).

Other Configurable Parameters

Number of Commands (up to 100 per Client)

Min Command Delay

Response Timeout

Retry Count

Command Error Pointer

Supported Message Types

Accepts Client Monitor and Control Messages

Supports all Edition 2 Causes of Transmission

Supported Data Types

Monitor Points:

M_SP_NA

M_DP_NA

M_ST_NA

M_BO_NA

M_ME_NA, NB, NC

M_IT_NA

Control Points:

C_SC_NA

C_DC_NA

C_BO_NA

C_RC_NA

C_SE_NA, NB, NC

Maximum number of points

(per Data Type)

1000 Points for all Supported Data Types, except

4000 total data words, maximum

Maximum number of commands

500 commands maximum for all four clients

Event Message Support

Timestamp events are transferred to the other protocol through the mailbox feature.

Configurable Parameters

t1 timeout set value

t2 timeout set value

t3 timeout set value

k (maximum queue)

w (latest ack threshold)

Specification

Description

Power Supply

24 VDC nominal
18 to 32 VDC allowed
Positive, Negative, GND Terminals
2.5 mm screwdriver blade

Current Load

500 mA max @ 32 VDC max

Operating Temperature

-4° F to 122° F (-20° C to 50° C)

Storage Temperature

-40° F to 185° F (-40° C to 85° C)

Relative Humidity

5% to 95% (with no condensation )

Dimensions

Standard:
 5.20 in H x 2.07 in W x 4.52 in D (13.2 cm x 5.25 cm x 11.48 cm)
Extended:
 5.20 in H x 2.73 in W x 4.52 in D
(13.2 cm x 6.934 cm x 11.48 cm)

LED Indicators

Power and Module Status
Application Status
Serial Port Activity
Serial Port Error Status

Configuration Serial Port

DB-9M RS-232 only
No hardware handshaking

Ethernet Port (Ethernet modules only)

10Base-T half duplex RJ45 Connector
Link and Activity LED indicators
Electrical Isolation 1500 V RMS at 50 Hz to 60 Hz for 60 s, applied as specified in section 5.3.2 of IEC 60950: 1991
Ethernet Broadcast Storm Resiliency = less than or equal to 5000 [ARP] frames-per-second and less than or equal to 5 minutes duration

Application Ports

Modbus Plus Connector
Two DB9 Female Standard Modbus Plus connectors

Serial Port Isolation

2500 V RMS port signal isolation per UL 1577
3000 VDC min. port to ground and port to logic power isolation

Shipped with Each Unit

Mini-DIN to DB-9M serial cables
4 ft RS-232 configuration cable
2.5mm screwdriver
CD (docs and Configuration utility)
RS-422/485 DB-9 to Screw Terminal Adaptor (1 or 4, depending on ports)