Printer friendly version of this page. Find a Distributor near you.

EtherNet/IP™ to PROFINET® IO Device Gateway


The EtherNet/IP™ to PROFINET® IO Device (slave) gateway offers bi-directional data transfers between EtherNet/IP™ controllers and a PROFINET® IO controller. The EtherNet/IP™ Driver supports I/O connections for guaranteed data delivery or Message instructions to send data to/from the PACs. The gateway supports 1440 bytes of input data and 1440 bytes of output data for larger applications.

In addition, the gateway’s multiple I/O connections, allow you to set different RPIs for control data and module diagnostics, enabling you to optimize your Ethernet bandwidth.


Click on image(s) to enlarge
Drag with the mouse. Click for close.

Características y Beneficios

  • Embedded EDS Add-On Profile allows for simplified integration and reduced configuration time for Rockwell Automation PACs.
  • No ladder programming is required when using I/O connections.
  • Multiple I/O connections allow you to set different RPIs for status and control data, enabling Ethernet bandwidth optimization.
  • Communication via an I/O connection provides guaranteed data delivery and enables the PAC to monitor for communication faults.
  • SD card slot (SD card optional) is used for storing configuration files in the event of a disaster.
  • ProSoft Discovery Service allows your PC to find the gateway and change its default IP address without being on the same subnet.
  • Video setup tutorial provided at


Number of Class 3 Server Connections


Supported PLC Types 


Supported Message Types


Number of Class 3 Client Connections

Connected - 2
Unconnected - 1

Number of Class 1 I/O Connections


Max I/O connection sizeIn/Out

496/496 bytes

Max RPI time

10 ms per connection

CIP Services Supported 

0x4C - CIP Data Table Read
0x4D - CIP Data Table Write

Command List

Support for 100 commands per Client, each configurable 
for command type, IP address, register to/from addressing
and word/bit count.

Command Sets 

PLC-2/PLC-3/PLC5 Basic Command Set
PLC5 Binary Command Set
PLC5 ASCII Command Set
SLC500 Command Set

Hardware Specifications

Power Supply

24 VDC nominal
10 to 36 VDC allowed
Positive, Negative, GND Terminals

Current Load 

24 VDC nominal @ 300 mA
10 to 36 VDC @ 610 mA maximum 

Operating Temperature 

-25°C to 70°C (-13°F to 158°F)

Storage Temperature 

-40°C to 80°C (-40°F to 176°F)


IEC 60068-2-27; 15G @ 11ms, 3-Axis (Operational)
IEC 60068-2-27; 30G @ 18ms, 3-Axis (Non-Operational)


IEC 60068-2-6; 5G @ 10 to 150 Hz

Relative Humidity

5% to 95% RH with no condensation

Dimensions (H x W x D)

5.38 x 1.99 x 4.38 in
13.67 x 5.05 x 11.13 cm

LED Indicators 

Configuration (CFG), Error (ERR), Power (PWR), 
Hardware Fault (FLT), Network Status (NS), 
EtherNet/IP™ Class I or Class III Connection Status 
(EtherNet/IP Only) Module Status (MS), ModuleConfiguration
Status (EtherNet/IP Only) Ethernet Communication
Port Link/Activity, and 100 mbit

Ethernet Port

10/100Mbit half-duplex RJ45 Connector Electrical Isolation
1500 Vrms at 50 to 60 Hz for 60 seconds, applied as
specified in section 5.3.2 of IEC 60950: 1991 Ethernet
Broadcast Storm Resiliency is less than or equal to
5000 [ARP] frames-per-second and less than or equal to
5 minutes duration

Shipped With Each Unit

2.5 mm screwdriver
ProSoft Solutions DVD
J180 Power Connector
5’ straight-through Ethernet cable 


Ex Certificate (ATEX Directive) 84,06 kB Última Modificación 22.05.2015
CB Safety 327,80 kB Última Modificación 22.05.2015
Korean KC Registration 548,37 kB Última Modificación 22.05.2015
Profibus/Profinet Certificate 63,29 kB Última Modificación 18.10.2018
UL/cUL; Class 1, Div 2 408,26 kB Última Modificación 22.05.2015
Declaration of Conformity (RoHS/CE) 297,32 kB Última Modificación 25.07.2018
EtherNet/IP - Declaration of Conformity 183,48 kB Última Modificación 01.08.2018