# DFCM.CFG # # This file contains the configuration for the ProTalk-DFCM communication # module. # # LOCATION : # DATE : # CONFIGURED BY : # MODIFIED : # # This section is used to define the configuration for the Module level # data. # [Module] Module Name : Test Example of PTQ-DFCM Communication Module Backplane Fail Count : 0 # Disable protocol when backplane error occurs # This section is used by the ProTalk module to define the data transferred between # the module and processor. # # Cmd Type --> 0=Disable, 1=Quantum to ProTalk, 2=ProTalk to Quantum, 3=Control # data block for module # DB Address --> address of starting word in database # Point Type --> 0=0x, 1=1x, 3=3x and 4=4x # Point Address --> point address (1 based)(0x and 1x must be at start of word (i.e., 1, 17, 33, ...)) # Word Count --> number of words to transfer (1 to 130) # [Backplane Data Exchange] # Cmd DB Point Point Word # Type Address Type Address Count START 1 0 4 1 100 #move data from Quantum to PTQ 2 100 4 101 100 #move data from PTQ to Quantum 3 3000 4 1001 64 #command control data area END # This section is used to define the configuration for the DF1 master device # simulated on Port 1. # [DF1 Port 1] Enabled : Yes #Y=Use port, N=Do not use port Type : M #M=Master, S=Slave Local Station ID : 1 #DF1 node address Protocol : H #F=Full-Duplex, H=Half-Duplex Termination Type : CRC #B=BCC, C=CRC Baud Rate : 19200 #Baud rate for port 110-38400 Parity : None #N=None,O=Odd,E=Even,M=Mark,S=Space Data Bits : 8 #5, 6, 7 or 8 Stop Bits : 1 #1 or 2 Minimum Response Delay : 0 #0-65535 mSec before sending response msg RTS On : 0 #0-65536 mSec before message RTS Off : 1 #0-65536 mSec after message Use CTS Line : N #Use CTS modem control line (Y/N) Response Timeout : 15000 #Response messgage timeout (0-65535 mSec) Retry Count : 2 #Response failure retry count ENQ Delay : 100 #0-65535 mSec before DLE-ENQ sent Minimum Command Delay : 10 #Minimum number of msec's between commands Error Delay Count : 100 #0-65535 Command cycle count if error First File : 7 #First file number for SLC simulation File Size : 200 #Number of elements in each file File Offset : 0 #Database offset for first file element [DF1 Port 1 Commands] # The file contains examples for a SLC 5/03 processor. # # LOCATION : # DATE : 06/24/99 # CONFIGURED BY : RAR # MODIFIED : # 07/23/99 -- Set to read more data file types. # START # 1 2 3 4 5 6 7 8 9 10 11 # Internal Poll Swap Node Func File File Elm Sub # Enable Address Interval Count Code Address Code Type # # Elm 1 100 0 10 0 3 501 N 21 0 0 0 0 10 0 1 509 N 7 10 END [DF1 Port 1 OVERRIDE DATA FILE MAPS] # DB File First Word # Address Number Element Length START 3500 100 0 100 3600 130 0 100 END # This section is used to define the configuration for the DF1 slave device # simulated on Port 2. # [DF1 Port 2] Enabled : Y #Y=Use port, N=Do not use port Type : S #M=Master, S=Slave Local Station ID : 3 #DF1 node address Protocol : H #F=Full-Duplex, H=Half-Duplex Termination Type : CRC #B=BCC, C=CRC Baud Rate : 19200 #Baud rate for port 110-38400 Parity : None #N=None,O=Odd,E=Even,M=Mark,S=Space Data Bits : 8 #5, 6, 7 or 8 Stop Bits : 1 #1 or 2 Minimum Response Delay : 0 #0-65535 mSec before sending response msg RTS On : 0 #0-65536 mSec before message RTS Off : 1 #0-65536 mSec after message Use CTS Line : N #Use CTS modem control line (Y/N) Response Timeout : 1000 #Response messgage timeout (0-65535 mSec) Retry Count : 2 #Response failure retry count ENQ Delay : 10 #0-65535 mSec before DLE-ENQ sent Minimum Command Delay : 100 #Minimum number of msec's between commands Error Delay Count : 100 #0-65535 Command cycle count if error First File : 7 #First file number for SLC simulation File Size : 200 #Number of elements in each file File Offset : 0 #Database offset for first file element [DF1 Port 2 Commands] # The file contains examples for a SLC 5/03 processor. # # LOCATION : # DATE : 06/24/99 # CONFIGURED BY : # MODIFIED : # # START # 1 2 3 4 5 6 7 8 9 10 11 # Internal Poll Swap Node Func File File Elm Sub # Enable Address Interval Count Code Address Code Type # # Elm 1 100 0 10 0 3 501 N 21 0 END [DF1 Port 2 OVERRIDE DATA FILE MAPS] # DB File First Word # Address Number Element Length START 3500 100 0 100 3600 130 0 100 END